| 
|
Fastenmaster
Decking Screws
- THE DECKING SCREW. FULLY TESTED.
Introducing the fastener engineered for the increased copper levels
found in the new ACQ pressure treated decking.
The design features of this FastenMaster product include:
- Coated with CR10
- Corrosion resistance.
- Colour matched to blend in with the new pressure treated
decking.
- Sharp threads quickly penetrate timber
- Deep #2 square drive virtually eliminates cam-out during
installation.
- Free driver bit included.
- Made in USA
- Length 63mm
- Boxes of 200 and New Bucket Size of 2200
|
|
|
Dextra Decking Screws
- Plated in zinc 15 microns to BS 3382 and coated in yellow passivate
to withstand up to 1000 (min) hours salt spray resistance.
- 25° Sharp point for easier penetration into all wood types.
- 40° Deep single thread to provide secure fixing with a high
pull-out resistance.
- Double countersunk and ribbed under the head to assist self-countersinking.
- Serrated threads on 45% of the screw and two flutes to achieve
optimum insertion into all wood types.
- Square drive to reduce driver wear and prevent ‘camming out’
Lubricated with yellow ‘Macalube’ to enhance screw insertion time,
extra driving torque and a greater resistance to corrosion.
- Full batch-traceability to the original steel mill certificate.
- Free square driver bit included in each box.
- Application Hints Screw should always be inserted at 90°. When
using a power driver the recommended speed should be 1,500 to 2,000
rpm. Ensure the free TIMco No. 2 square drive bit is used.
- Boxes of 200 screws & Buckets of 1000 screws
- Length 50mm
- Attractive 'gold' type colour
|
 |
"Carpenters Mate " Bugle Head,
Square Drive Stainless Steel Decking Screws
- 10mm diameter #2 Square Drive Bugle Head
- "Beaver Bite" type
17 auger point for extra fast starts
Boxes of 350 No10 x 50mm (2 inch)
Boxes of 1750 No10 x 50mm (2 inch)
Boxes of 350 No10 x 63mm (2 1/2inch)
Boxes of 1750 No10 x 63mm (2 1/2inch)
"Carpenters
Mate" Stainless Steel
Finishing Screws for Decking
- 6mm diameter #2 Square Drive Trim Head
- "Beaver Bite" type 17 auger point for extra
fast starts
- Coarse threads approximately 2/3 up shank draw board
tightly to substrate
- Pre-drilling always recommended, and a must near board
ends to prevent splits
- Slender #7 shank for finish work and trim
- Use on decking jobs with stable hardwoods & wood
substitutes when screw heads need to be hidden
- Very small head
- "Carpenters Mate " is a UK brand
- Boxes of 350 or 1750
- Available in 50mm and 63mm length
|
|
"Swaneze" Bugle
Head, Square Drive Stainless
Steel Decking Screws |
|
| · |
First introduced in 1989, the Swaneze was the
first stainless steel deck screw. |
| · |
.344" diameter #2 Square Drive Bugle
Head |
| · |
"Beaver Bite" type 17 auger point for
extra fast starts |
| · |
Coarse threads approximately 2/3 up shank draw
board tightly to substrate |
| · |
Pre-drilling always recommended, and a must
near board ends to prevent splits
"SWANEZE" is a respected
USA brand |
|
|
Boxes of 350 No8 x 50mm (2 inch)
Boxes of 1750 No8 x 50mm (2 inch)
|
|
"SWANEZE" STAINLESS
STEEL FINISHING SCREWS FOR DECKING
- 230" diameter #1 Square Drive Trim Head
- "Beaver Bite" type 17 auger point for extra
fast starts
- Coarse threads approximately 2/3 up shank draw board tightly
to substrate
- Pre-drilling
always recommended, and a must near board ends to prevent splits
- Slender #7 shank for finish work and trim
- Use on decking jobs
with stable hardwoods & wood substitutes when screw heads
need to be hidden
- Very small head
- 316 stainless steel "SWANEZE" strongly
recommended for seaside applications and any situation where non
rust longevity is a priority
- "SWANEZE" is a respected USA brand
- Boxes of 350 or 1750
- Available in 50mm and 63mm length
|
|
|
